Обновление микропрограммы NEX-VG10E (Windows)

Important notes:

• When performing the firmware upgrade, please use a fully charged rechargeable battery pack NP-FV70 / NP-FV100 (sold separately) or the AC adapter AC-PW10AM.
• Do not remove the battery or AC adapter during the upgrade; otherwise, the camcorder may become inoperable due to the sudden power shutdown.
• Remove the memory card from the camcorder beforehand.

Step 1: download the firmware upgrader

1. Make sure that you are logged on as a user with administrative rights.
2. After reading the disclaimer, click the [Accept] button below.
3. The download of the [NEX-VG10V3_Update1112a.exe] file (56.8MB (59 597 936 bytes)) will start.
4. Save the file to the desktop of your computer (recommended).

Step 2: upgrade the firmware of your camcorder

1. Close all currently running programs on your computer.
2. Double-click the [NEX-VG10V3_Update1112a.exe] file you downloaded to start up the Firmware Updater.
   
   
   The Firmware Updater window appears.
   
   
3. If it has not been done already, remove the memory card from the camcorder.
4. Connect the camcorder to the computer with the supplied USB cable.
   Note: When the camcorder is connected to the computer, the LCD screen of the camcorder turns off. Please proceed to the next step.
   If the LCD screen of the camera does not turn off, please try one of the following methods:
   • Disconnect the USB cable from the camera, then reconnect the USB cable.
   • If there is another free USB terminal on the computer, reconnect the USB cable to this terminal.
5. Confirm the "Safely Remove Hardware" icon is displayed on the task tray at the lower right corner of the computer screen.
   Note: If is not displayed on the task tray, please proceed to the next step.
6. After confirming the above, click Next on the Firmware Updater window. Figure 1 appears on the Firmware Updater window, and Figure 2 appears on the LCD screen of the camcorder.
   Note: From now on, never turn off the camcorder until the firmware upgrade is completed.
   
   Figure 1
   
   
   Figure 2
   
   
   
7. After confirming the screens on Figures 1 and 2, click Next. The current version and the version after the upgrade appear on the lower left part of the screen. (Figure 3)
8. After confirming Current version is ver.1 or ver.2, click Next.
   
   If the screen on Figure 4 appears, the upgrade is not required. According to the message, stop the USB connection and click Finish. Turn off the camcorder, remove the battery pack and/or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camcorder.
   
   Figure 3: Update is required
   
   
   Figure 4: Update is not required
   
   
   
9. Click the "Safely Remove Hardware" icon on the task tray at the lower right corner of the computer screen to stop the USB connection, as instructed on figure 5.
   Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.
   Note: If is not displayed on the task tray, please proceed to the next step.
   
   Figure 5
   
   
   
10. Press the center of the control wheel to execute the reset of the camcorder.
    
    
    Note: The screen turns off when the center of the control wheel is pressed. Please proceed to the next step.
    
    
11. Click Next on the Firmware Updater window.
12. After resetting, reconnection of the camcorder is verified, and the screen on Figure 6 appears.
13. Click Run to start the upgrade. The progress bar appears while upgrading (approximately 5 minutes).
    Note: Never turn off the camcorder nor disconnect the USB cable while upgrading.
    
    Figure 6
    
    
    
14. When the upgrade is completed, the screen on Figure 7 appears. Click Finish.
    
    Figure 7
    
    
    
15. Click on the task tray at the lower right corner of the computer screen to stop the USB connection.
    Note: If is not displayed on the task tray, please proceed to the next step.
16. Disconnect the USB cable.
17. Turn off the camcorder, remove the battery pack and/or the AC adapter, reinsert the battery or reconnect the AC adapter and turn on the camcorder.

Step 3: Confirm the firmware version of your camcorder is Ver.03.

1. Select Menu --> Setup --> Version on the camcorder.
2. The firmware version is displayed as illustrated below.
   
   

Step 4: Download the manuals describing the new available functions and how to use them.

All the new functions detailed in the below manuals are included in this firmware upgrade (Ver.03.).

• Download the new function manual (from Ver.02 to Ver.03)